Dropd94Ranger
Forum Member
Engine bay looks GREAT! It's such a pain to get any detail even close to that. Good job! I've worked on a few engine bays like that and they didn't even turn out to what I would have liked...
hsean1 project
- Thread starter hsean1
- Start date
alittle update
i spent a couple of hours sandblasting these parts and epoxy primering them
this is my oem cobra lower intake that a friend repaired for me i forgot to snap a before pic.the guy i bought it from snapped a tap in there and cut a big section off of it. it was completed drilled out and aluminum welded back in i set the spot so it can be rethreaded.
new 1993 cobra r brake booster that i sanded and painted body color
i also sanded down my new power steering rack and epoxy primered then painted body color as well
in epoxy primer
painted 2009 corvette cyber grey
the wiper motor
i installed the black dash and sound deadened the interior but my camera flash is bad for some reason
[I
MG]http://i150.photobucket.com/albums/s95/hsean/s2.jpg[/IMG]
painted this black and cleared it
i spent a couple of hours sandblasting these parts and epoxy primering them
this is my oem cobra lower intake that a friend repaired for me i forgot to snap a before pic.the guy i bought it from snapped a tap in there and cut a big section off of it. it was completed drilled out and aluminum welded back in i set the spot so it can be rethreaded.
new 1993 cobra r brake booster that i sanded and painted body color
i also sanded down my new power steering rack and epoxy primered then painted body color as well
in epoxy primer
painted 2009 corvette cyber grey
the wiper motor
i installed the black dash and sound deadened the interior but my camera flash is bad for some reason
[I
MG]http://i150.photobucket.com/albums/s95/hsean/s2.jpg[/IMG]
painted this black and cleared it
foxbodydave
Club Member
damn its comin along nicely. whats your next steps gonna be??
thanks dave , i installed the k-member last night and i have a small gash on my forehead as a reminder.the damn stop on one of the nuts broke off as i was tightening the bolts and got hit hard.i thought i might need a couple of stitches but i got the bleeding to stop after a few minutes.the funny thing is it could have been my eye and i had safety glasses in my pocket.right now the funds are low with christmas and all. i have two small children under 6 but i already have the new black carpet and i could finish the interior but i need the t-top seals and that is going to cost me some change.i am going to focus on the front suspension i have new 93 cobra r spindles and 13" rotors i am going to do a five lug conversion.
SVT32VDOHC
Club Member
That design for the rear seat will work. And it's much less time than I spent with how I mounted mine on my 81 coupe. I took the brace out of the 94-04 car and mounted it in the fox. That was a lot of holes to drill out. I don't know what do do this time around.
i came up with it on the fly with some metal i had sitting around the garage. i i did get the plastic brackets that the front of the 03 rear seat snap into.i have to borrow my friends welder again and fabricate a bracket to set the plastic insert into.they should snap right in then as long as i measure right:thumbsup:
not anywhere as much detail as your build that cage is a work of art
thanks ,i still have to do the door panels i am doing something custom there too.the ambient lighting is a really cool feature it changes to more than 6 colors i ran alot of wiring with it when this thing is done it's going to draw some attention.
good catch it isn't staying that way it will be a complete oval all the way around the controls and i want to get the billet style controls and faceplate. i also have to extend the faceplate at the top and bottom and that the whole thing will be out of stainless steel as well. i also want to do the shifter plate around the shifter boot.