Fryguy302
Club Member
Precision Billet 98mm CEA Turbo, g-trim, 1.32 a/r exhaust housing, low passes, made 2000hp on small block, $1950obo
Comp Cams Solid Roller Lifters for SBF, stock diameter, used but not much time on them, good shape $200
TFS Twisted Wedge Heads, with roller rockers, no port work, set up for hyd roller lifters, $1100 obo
Shorty headers for BBF, fits 70's trucks and others, stainless, $250
Edelbrock EFI 5.0 intake for 302, *lower intake only* can be used with Edelbrock upper or Pro Products uppers, $75
Pro Products billet TFI/EFI distributor for 302/351 (two bases), $100 shipped.
DSS 351 short block, forged pistons, girdle, ARP Hardware, very low miles but needs some clean up as it sat around a while.
Hooker Super Comp Headers and dual exhaust for SBF in early mustang or comet, $200obo
Rage head and neck restraint, cost $600+, will sell for $300obo
Edelbrock Super Victor intake manifold for 9.5 deck SBF, 4150 flange, (2924), $200
Racecraft Weld-on Caster/Camber plates also brand new, never used, $100
Solid Roller Cam for SBF, like new, idle time only, 268/282 deg duration @ .050 lift, .721/.704 lift, 112 lobe sep, $150
DFI Gen 6, old school EFI box with harness for Turbo V6 Buick, $250
13-14 Mustang GT mufflers and tailpipes, removed from brand new car, less than 10 miles, $50obo
65 Comet front and rear bumers, good shape, $150 for both
65 Comet hood, holes for pins but no rust ever, $100
Everything below this line is between Free and $25
______________________________________________________________________________
70 Cougar gas tank, good shape, $25
65 Comet Rear Seat, needs cover, $20
70 Cougar/Mustang Power Steering Pump, was on 351c, (free)
70 Cougar/Mustang 351C air filter assembly, $20
87 Grand National Header Panel (needs minor repair), $25
2010 Mustang Wiper arms, motor, etc, $25
2010 Mustang box of misc. parts, stock airbox, etc, $10
78-88 G-Body HVAC Block-Off panel, $20
LS1/LS2/LS6 stock rocker arms, low mileage $25
Comp Cams Solid Roller Lifters for SBF, stock diameter, used but not much time on them, good shape $200
TFS Twisted Wedge Heads, with roller rockers, no port work, set up for hyd roller lifters, $1100 obo
Shorty headers for BBF, fits 70's trucks and others, stainless, $250
Edelbrock EFI 5.0 intake for 302, *lower intake only* can be used with Edelbrock upper or Pro Products uppers, $75
Pro Products billet TFI/EFI distributor for 302/351 (two bases), $100 shipped.
DSS 351 short block, forged pistons, girdle, ARP Hardware, very low miles but needs some clean up as it sat around a while.
Hooker Super Comp Headers and dual exhaust for SBF in early mustang or comet, $200obo
Rage head and neck restraint, cost $600+, will sell for $300obo
Edelbrock Super Victor intake manifold for 9.5 deck SBF, 4150 flange, (2924), $200
Racecraft Weld-on Caster/Camber plates also brand new, never used, $100
Solid Roller Cam for SBF, like new, idle time only, 268/282 deg duration @ .050 lift, .721/.704 lift, 112 lobe sep, $150
DFI Gen 6, old school EFI box with harness for Turbo V6 Buick, $250
13-14 Mustang GT mufflers and tailpipes, removed from brand new car, less than 10 miles, $50obo
65 Comet front and rear bumers, good shape, $150 for both
65 Comet hood, holes for pins but no rust ever, $100
Everything below this line is between Free and $25
______________________________________________________________________________
70 Cougar gas tank, good shape, $25
65 Comet Rear Seat, needs cover, $20
70 Cougar/Mustang Power Steering Pump, was on 351c, (free)
70 Cougar/Mustang 351C air filter assembly, $20
87 Grand National Header Panel (needs minor repair), $25
2010 Mustang Wiper arms, motor, etc, $25
2010 Mustang box of misc. parts, stock airbox, etc, $10
78-88 G-Body HVAC Block-Off panel, $20
LS1/LS2/LS6 stock rocker arms, low mileage $25
Last edited:
