Fresh 408 forsale

90_Notch

90_Notch

Forum Member
SOLD!!!!!!!!!!!!!!!!!!!

Sitting onthe engine stand. 3300 obo
408 stroker R block 4 bolt mains on 2/3/4
Eagle rotating assembly
Probe flat top pistons
Canton oil pan w/pickup
New tci flex plate
new balancer
new HVoil pump
new oil pump shaft
edelbrok waterpump
polished aluminumn under drive pullys
aluminum ford motorsport valve covers
ARP head bolts
Everthing is new this year engine just back from the machine shop my lose your gain need this thing to move out ASAP have my new motor

You should only need heads, cam, lifters, intake,carb for this. Everything is new some of it still in boxes.
Kooks headers 2" primaries 3 1/2" collectors with bullets attached
with the adapter plates

Don't want to seperate. I would probably just keep it and buy me a FOX to put it in.


This motor ran 10.58 on motor this year at 129 with a 1.493 60'. This set up was with mild hyd cam.


SOLD!!!!!!!!!!!!!!!!!!!!!!!!
 
Last edited:
what a smokin ass deal, if I could sell my shit I would be all over that, know anybody that wants a 408?
 
wish i did.
Wouldn't need much to make this a 9 sec motor. I had a BS top end. I had it set up for street more than strip and still hit 10.50's. Guy from New Jersey offered my 3k.
I would take that if i got to keep the oil pan. i'm ready to deal too so nothing is out of the question.
Everything i have for this goes with this. There's only a few things missing for the top half.
Blocks almost 1800 alone with no finish work i paid 1700 for the finish work.



M-6010-N351* 9.500" Deck Height

Cast iron block with 4-bolt main caps on journals 2, 3, and 4

Nodular iron main caps

Can be bored/stroked to produce 434 cu. in.

Non-siamese cylinder bores

Bore range from 4.000-4.030"

Wet sump oiling design

2.749" main journal diameter

Weighs approximately 205 lbs.

High-strength block for professional competition (Circle Track, Drag Racing)

Semi-finished main bearing bores and lifter bores – must be honed to fit
 
Last edited:
Will sell just the short block/balancer/flexplate
2500
Can't sell the other stuff seperate until the short bock is gone.
 
90_Notch said:
Will sell just the short block/balancer/flexplate
2500
Can't sell the other stuff seperate until the short bock is gone.
Click to expand...
OMG! that is a deal, you can even build a stock block stroker for that much!
 
team_southside said:
what heads are the headers for ??
Click to expand...
I have the adapter plate so diag or straight. the headers are diag.
so the plate goes from an inline head bolt pattern to diag header pattern.
 
Really need this thing to go. For 3500 firm I'll throw in my 1000 CFM pro system carb which cost me 900 dollars by the time it was all done up.
 
Well this guy hasn't contacted me yet and i don't know if i should just try an sell to the next guy or what.
I e-mailed him with my paypal and the total as he requested.
Then i e-mailed him with everything i packed up.
I guess it's stll forsale no cash in hand. Here's what's on the pallet
3000 and it's yours it's all packed now so it's all going together.
1-R block Assembled short block with eagle rotating assembly w/ probe pistons
2-canton oil pan
3-canton pickup
4-HV oil pump
5-oil pump shaft
6-Powerforce plus balancer
7-TCI flexplate
8-aluminum UD pulleys (water and crank)
9-timing cover
10-timing cover bolts, pointer
11-aluminumn valve covers
12-metal reusable valve cover gaskets
13-ARP valve cover bolts
14-ARP intake bolts
15-ARP head bolts
16-chrome water neck (with allen bolts)
17-upper and lower radiator hoses
18-Edelbrok water pump (with bolts for UD pulley)
19-Chrome alternator
20-3 1/2" bullets
21-ARP flexplate bolts
22-oil pan bolts
23-Hardened allen head trans bolts
24-Some misc bolts
 
You must log in or register to reply here.
Back
Top