rockher_man
Forum Member
1956 F100 Custom Cab SOLD...PARTS still available!
My F100 truck is SOLD....
ALL PARTS STILL AVAILABLE!..........
PARTS LIST: NOT installed...most NEW in BOXES!!!
2[SUP]nd[/SUP] set of original rear fenders with spare tire cut-out on driver side fender ---almost NO rust.
1970 F100 9-INCH rear axle housing with all brackets removed & cleaned up.
Ford 9-inch Big (Torino) Bearing Rear Disc Brake Conversion kit…. rotors are 5 x 4 ½ Ford pattern…
Ford Racing Parts # M-4204-F28A, TRAC-LOC Limited Slip, with 1536-steel billet case caps.
ALL bearings & gaskets needed to assemble rear pumpkin….
NASCAR Ford 9-inch 3:89 ring and pinion set --- Back-cut gears!
New Dutchman 28-spline Street/Strip axles & retainers with bearings…NEED axle SEALS!
Extra “hooded” Daytona pinion bearing support without races/bearings.
1956 Running boards --- need a few repairs.
2[SUP]nd[/SUP] set of “short” cab-length running boards…I was going to use these to repair the long ones!
Total Cost Involved Mustang II style independent front suspension with tubular A-arms and
air springs with sway bar…rotors are 5 x 4 ½ Ford pattern…
No Limit Engineering FAT BAR 4-bar parallel rear suspension with air ride, includes panhard bar!
Accuair Stage II management system with ride height sensors, key fobs, EVERY option available!!!….best of the best!
12-gallon 8-port D.O.T.approved air tank for air ride system.
Art Morrison Enterprises 2" x 4" square steel tubing for NOTCHES…..bent the “hard way”…you can view them here……
http://artmorrison.com/layout.php?y=frames/&x=framekit
Look for a section labeled: Special Bends Also Available!
ALSO AVAILABLE!…
Probe Industries SRS #10666-030 flat top pistons Net Head Volume (cc) -4.0.
...and...
Clevite Perfect Circle Ring Set: #315-0049-030 1/16" - 1/16" - 3.0mm (std. oil ring)
Early 60’s SMALL BLOCK FORD Buddy Barr/Holley TRI POWER set up!!!
ALL these parts are listed here seperatley...email me with any questions or for more pic's...
-
My F100 truck is SOLD....
ALL PARTS STILL AVAILABLE!..........
PARTS LIST: NOT installed...most NEW in BOXES!!!
2[SUP]nd[/SUP] set of original rear fenders with spare tire cut-out on driver side fender ---almost NO rust.
1970 F100 9-INCH rear axle housing with all brackets removed & cleaned up.
Ford 9-inch Big (Torino) Bearing Rear Disc Brake Conversion kit…. rotors are 5 x 4 ½ Ford pattern…
Ford Racing Parts # M-4204-F28A, TRAC-LOC Limited Slip, with 1536-steel billet case caps.
ALL bearings & gaskets needed to assemble rear pumpkin….
NASCAR Ford 9-inch 3:89 ring and pinion set --- Back-cut gears!
New Dutchman 28-spline Street/Strip axles & retainers with bearings…NEED axle SEALS!
Extra “hooded” Daytona pinion bearing support without races/bearings.
1956 Running boards --- need a few repairs.
2[SUP]nd[/SUP] set of “short” cab-length running boards…I was going to use these to repair the long ones!
Total Cost Involved Mustang II style independent front suspension with tubular A-arms and
air springs with sway bar…rotors are 5 x 4 ½ Ford pattern…
No Limit Engineering FAT BAR 4-bar parallel rear suspension with air ride, includes panhard bar!
Accuair Stage II management system with ride height sensors, key fobs, EVERY option available!!!….best of the best!
12-gallon 8-port D.O.T.approved air tank for air ride system.
Art Morrison Enterprises 2" x 4" square steel tubing for NOTCHES…..bent the “hard way”…you can view them here……
http://artmorrison.com/layout.php?y=frames/&x=framekit
Look for a section labeled: Special Bends Also Available!
ALSO AVAILABLE!…
Probe Industries SRS #10666-030 flat top pistons Net Head Volume (cc) -4.0.
...and...
Clevite Perfect Circle Ring Set: #315-0049-030 1/16" - 1/16" - 3.0mm (std. oil ring)
Early 60’s SMALL BLOCK FORD Buddy Barr/Holley TRI POWER set up!!!
ALL these parts are listed here seperatley...email me with any questions or for more pic's...
-
Last edited:
