FLAGMANBILL
Club Member
1978 Malibu 25.5 Chassis roller $7500
Focusing on finishing my degree, and moving to Florida in the next 2 years, and don't have time or effort to devote to building the car, so I feel its time to go. I've got tons and tons of pictures available if needed. I can be reached on my cell @ 734-323-8821.
car has clear title.
Body/Car:
Pro Race Craft Engineering built 25.5 chassis, finished last year
Car has been mini tubbed with competition engineering 36 in wheel tubs
Frame has been notched and clearanced to fit M/T 29.5/10.5
12 bolt chevelle rear end (from a 1969) with moser axles, and strange light weight spool. 4:33 gears
Glasstech fiberglass front and rear bumpers
Harwood 6 inch outlaw lift off hood, drilled for hood pins, which are installed
All interior plastics are included, as well as rear seat, which is rough and could be recovered, and reinstalled after side foams are trimmed for fully functional back seat look.
1 Kirkey pro street drag seat, 18 or 19 inch, cant remember
Interior is completely gutted, and ready for race car wiring, no dash, was cracked terribly.
25.5 cage and every bar has 3 coats of VHT satin roll cage paint on it, ($100 in paint alone)
Needs fresh paint, LH ¼ panel dent bumped out from racing pre cage without anti roll bar, (small dent)
LH ¼ has small amount of rust at wheel well on bottom, minor.
Car has paint chips here and there as its 20 plus years old.
Car is setup for BBC with motor plate.
TNT raceshop alum. CNC cut motorplate for Gbody
Chassis engineering midplate
Hooker Supercomp 2241 BBC G-body headers with slip tubes
Frame has been painted, wire wheeled, and had a fewbody mount holes repaired by the Fab Shop, also had inner frame rail boxed. Frame is amazing, and one of the cleanest frames on a gbody I’ve seen, I pulled the factory frame out cause it was rusty, and broke in one spot when I bought the car.
TNT raceshop alum body mount bushing+ 25.5 cage is about is ridged as I could make the chassis
Moroso front tires with Weld prostars, rear is a Prostar knock off
Car comes with 29.5x10.5’s (m/t) and 29. True tens (hooser)
more pictures here:
http://motownmuscle.com/forums/showthread.php?162103-Huge-thanks-to-Rich-at-PRE&highlight=
Focusing on finishing my degree, and moving to Florida in the next 2 years, and don't have time or effort to devote to building the car, so I feel its time to go. I've got tons and tons of pictures available if needed. I can be reached on my cell @ 734-323-8821.
car has clear title.
Body/Car:
Pro Race Craft Engineering built 25.5 chassis, finished last year
Car has been mini tubbed with competition engineering 36 in wheel tubs
Frame has been notched and clearanced to fit M/T 29.5/10.5
12 bolt chevelle rear end (from a 1969) with moser axles, and strange light weight spool. 4:33 gears
Glasstech fiberglass front and rear bumpers
Harwood 6 inch outlaw lift off hood, drilled for hood pins, which are installed
All interior plastics are included, as well as rear seat, which is rough and could be recovered, and reinstalled after side foams are trimmed for fully functional back seat look.
1 Kirkey pro street drag seat, 18 or 19 inch, cant remember
Interior is completely gutted, and ready for race car wiring, no dash, was cracked terribly.
25.5 cage and every bar has 3 coats of VHT satin roll cage paint on it, ($100 in paint alone)
Needs fresh paint, LH ¼ panel dent bumped out from racing pre cage without anti roll bar, (small dent)
LH ¼ has small amount of rust at wheel well on bottom, minor.
Car has paint chips here and there as its 20 plus years old.
Car is setup for BBC with motor plate.
TNT raceshop alum. CNC cut motorplate for Gbody
Chassis engineering midplate
Hooker Supercomp 2241 BBC G-body headers with slip tubes
Frame has been painted, wire wheeled, and had a fewbody mount holes repaired by the Fab Shop, also had inner frame rail boxed. Frame is amazing, and one of the cleanest frames on a gbody I’ve seen, I pulled the factory frame out cause it was rusty, and broke in one spot when I bought the car.
TNT raceshop alum body mount bushing+ 25.5 cage is about is ridged as I could make the chassis
Moroso front tires with Weld prostars, rear is a Prostar knock off
Car comes with 29.5x10.5’s (m/t) and 29. True tens (hooser)
more pictures here:
http://motownmuscle.com/forums/showthread.php?162103-Huge-thanks-to-Rich-at-PRE&highlight=
Last edited:
