Recent content by 89-LX

Anyone willing to rent me or let me borrow their cherry picker and engine plate if someone has one for a 302 Ford for a day or two? Not interested in buying, don't have the room for it. Thanks

Just curious if anyone took their car to Lids dyno day?

Just found out today that the city won't split the property. The property is 1350' x 326'. The piece the current owner want to split and give us is the front part, that's about 250' x 250'. The current township zoning ordinance states "All lots shall not be three (3) times longer than their...

Anyone here happen to be a surveyor or know one? Looking at getting a quote to get some land surveyed.

Quick question regarding Michigan monitor. I was stopped at a light, and someone clipped my rear bumper. Most damage is just scratches, but require the bumper to be blasted and painted again, which comes in at the cost of about $500-$550 plus $200 to replace the plastic lower bumper that is...

Before I bite the bullet on a new set of tires in the spring, I was wondering if anyone had a 4 lug wheel, with a 295 wide 28" tall tire on it I could just bolt to my fox to check clearances? The tire I'm looking to run is a 295/50/16 on a cobra r wheel. Hoping it will work as my 255/50/16 e/t...

So a little background on the car. Last year, I blew the HG but the var ran great and strong. So in the fall, I stripped the upper half down and had the heads decked. The engine sat all winter, until I got it together this spring. Its a standard 302, with an on3 single turbo, h/c/i. MSD Digital...

Just curious if anyone on the east side has a shop press that can press an input shaft bearing onto a T5 input shaft for me? Kind of in a bind and work screwed me with being able to get it done yesterday. I'm in Chesterfield, but willing to travel around. All auto shops around here want $70 to...

Looking to use one to test my fuel pressure at WOT. I have a hand held gauge, but the line isn't long enough to reach the cowl to mount it there temporary for testing. Trying to figure out my fuel issue, and why I believe the pressure is falling off.

Never had this issue pre-turbo, but after putting the turbo on with a dynomax race bullet and a turn down after,, the car leaves a black soot exhaust on the cement. The wife is getting pist at me, that I'm "ruining" the driveway. It seems like it happens more when the car is cold and first...

Does anyone make a thin t-bolt clamp? I keep popping off the TB hose with my BBK throttle body, because there isn't enough lip area to hold the t bolt clamp. As soon as I get it nice and tight, the pressure pushes it off. I had a worm clamp on there before which held, but after I removed and...

Having a fuel issue with the Mustang, and I need to find a fuel pressure gauge to run some tests. Not looking for a hand held one that goes on the schrader valve, as I need to test it under load. Just wondering if anyone had a cheap one laying around that I could scoop up? Want to replace a few...

Just wondering if anyone had a FWD bearing puller tool that I could possibly borrow or rent for the day. http://www.harborfreight.com/fwd-front-wheel-bearing-adapters-66829.html It's one like that. Just looking to do some minor maintenance, and not looking to yank the entire knuckle out to do...

Well after some working on the price, I can actually afford to sell it cheaper then than my $6500 I mentioned earlier. Hoping I can get close to low $6k, but still can go lower now. Just picked up this nice little gem today:

So I'm looking to sell my vehicle, and I was wondering if I could get some feedback from you guys on my price for it. Off the bat, I was thinking $6900. KBB in good condition is $6,945, and fair is $6,465. Here is the specs on it: 2007 Mercury Mariner Premier 3.0L V6 4WD 143,000 Miles Oil...