igotaneed4speed
Club Member
Racing Garage sale, lots of stuff, taking offers!
I have alot of misc. stuff laying around I don't need so its all up for sale.
This is a quick of my head listing I have lots of stuff not on here yet that will get added daily...
Sport comp black face gauges all are 2 1/16th
$40 - elec oil press(no sender)
$30 - elec coolant temp (no sender)
$30 - elec trans temp(no sender)
$80 - pyrometer temp
$60 for both - Two MSD GM2 coil packs (ms-8224) These have maybe three hours run time on them were used with a haltec ecu driven by two msd5 boxes on my glh way back when. I have the adaptor blocks to run them with msd ignition but i cut some wires off so they may be of no use but will be included with coils.
$70 - Two MSD 5 boxes, One of these works the other got dropped and hasn't worked since. I do not remember which is which so you can have both.
$200 - Ford Top Loader 28 spline, I have to pull the serial number to find out if its wide or close ration I do not remember. Pics at request
There is no tag on this for me to Part id the trans - have no clue if its close or wide ratio...
Two 440 blocks,
$350 - 1973, Steel crank 440T, This is a short block with some open chambers heads that came off of it complete to oil pan, no intake.
$175 - year unknow, will check when i get home. Bare 440 block with caps
$300 o.b.o - Lakewood blow thru bellhousing
This is NEW was used in mock up only... comes with hardware and block protector plate.
http://www.lakewoodindustries.com/P...jID=152&minID=1521&selection=0&minselection=0
$20 each for in packages, $15 for the opend one - Jegs Roller rockers SBF, 1.6, 7/16. Two are new in packages, one is open but un-used.
$300 obo - Wilden Pump; The smaller version of these pumps that we use at work alot go for more than what I'm asking for this one. It is tagged 99' but has never been used. I tired to find details on the pump from the part number but not getting to far with it. I would assume if you looking to buy this you prob know what it is more than me.
here is a link to a wilden catalog that has a part # break down guide.
http://www.wildenpump.com/eoms/PX4-ORG-MTL-EOM-01.pdf
(PN there is 04-5000-01)
$500 - OMC outdrive, gimbal, lift rams and pump, coupler, prop, ect... This is a complete 3.0 take out form a boat It comes with everything minus the engine. Has new U-joints, support bearing, flywheel, bellhousing, coupler and water pick up. Outdrive was freshedned by local Marine shop and all parts are new, I have receipts to prove this.
Gimbal part # 983900
Outdrive part # 983841
$100 - JGS percision blow off valve, mounted on stell cold pipe
$ 75 - Mile Marker Hubs - NEW Ford Applications Part # 449
$40 - Black Magic Mustang specific Fan - Temp controller does not work has to be switch wired.
$100 - Coleman dry sump oil tank
I have alot of misc. stuff laying around I don't need so its all up for sale.
This is a quick of my head listing I have lots of stuff not on here yet that will get added daily...
Sport comp black face gauges all are 2 1/16th
$40 - elec oil press(no sender)
$30 - elec coolant temp (no sender)
$30 - elec trans temp(no sender)
$80 - pyrometer temp
$60 for both - Two MSD GM2 coil packs (ms-8224) These have maybe three hours run time on them were used with a haltec ecu driven by two msd5 boxes on my glh way back when. I have the adaptor blocks to run them with msd ignition but i cut some wires off so they may be of no use but will be included with coils.
$70 - Two MSD 5 boxes, One of these works the other got dropped and hasn't worked since. I do not remember which is which so you can have both.
$200 - Ford Top Loader 28 spline, I have to pull the serial number to find out if its wide or close ration I do not remember. Pics at request
There is no tag on this for me to Part id the trans - have no clue if its close or wide ratio...
Two 440 blocks,
$350 - 1973, Steel crank 440T, This is a short block with some open chambers heads that came off of it complete to oil pan, no intake.
$175 - year unknow, will check when i get home. Bare 440 block with caps
$300 o.b.o - Lakewood blow thru bellhousing
This is NEW was used in mock up only... comes with hardware and block protector plate.
http://www.lakewoodindustries.com/P...jID=152&minID=1521&selection=0&minselection=0
$20 each for in packages, $15 for the opend one - Jegs Roller rockers SBF, 1.6, 7/16. Two are new in packages, one is open but un-used.
$300 obo - Wilden Pump; The smaller version of these pumps that we use at work alot go for more than what I'm asking for this one. It is tagged 99' but has never been used. I tired to find details on the pump from the part number but not getting to far with it. I would assume if you looking to buy this you prob know what it is more than me.
here is a link to a wilden catalog that has a part # break down guide.
http://www.wildenpump.com/eoms/PX4-ORG-MTL-EOM-01.pdf
(PN there is 04-5000-01)
$500 - OMC outdrive, gimbal, lift rams and pump, coupler, prop, ect... This is a complete 3.0 take out form a boat It comes with everything minus the engine. Has new U-joints, support bearing, flywheel, bellhousing, coupler and water pick up. Outdrive was freshedned by local Marine shop and all parts are new, I have receipts to prove this.
Gimbal part # 983900
Outdrive part # 983841
$100 - JGS percision blow off valve, mounted on stell cold pipe
$ 75 - Mile Marker Hubs - NEW Ford Applications Part # 449
$40 - Black Magic Mustang specific Fan - Temp controller does not work has to be switch wired.
$100 - Coleman dry sump oil tank
Last edited:
