Anyone know how or know someone that can wire cars

T

tewkes28

Club Member
I'm looking for someone to install a painless 12 circuit harness in a 1972 Dodge Demon. The previous owner ripped out the half ass wiring harness, and bought the painless one, but couldn't figure out how to install it.

If anyone knows anybody that can do this professionally and reasonably priced email me at [email protected]

I talked to one guy that might be able to do it but he wouldn't give me an estimate of price. I'm not looking for a concrete price but something in the ball park of a couple hundred bucks. Thanks

Bryan
 
are all the circuit ends there(plug ins) what all do you want wired dash lights,radio,heating and cooling,dome light,head and tails?
 
PM DUKE on here. he doesn't check it too often so if lists an email u might wanna send something to both.. Dunno if he has free time, but he knows his stuff
 
Thanks, I'll try to email him.

Basically I need the dash, engine, and all accessories wired. The car doesn't have heat, a/c, and any other creature comforts.
 
tewkes28 said:
Thanks, I'll try to email him.

Basically I need the dash, engine, and all accessories wired. The car doesn't have heat, a/c, and any other creature comforts.
Click to expand...


How long of a turn around are you looking to have this done in? It would take me prob a week or better to get it done.. But im willing to do it .. 200 bucks.. let me know.
 
Blackbirdws6zzz said:
sorry for thread jacking but I also may need someone to put another wiring harness in my mustang! Starting fresh!
Click to expand...


EFI or carb and what do you have already as in what harness what are you going to etc..
 
I want the 351 to be EFI and it's going to be an auto for now unless I magically find a nice t-5 laying around for cheap. but for now auto. It's a 89. I have a while to go on the motor though but I will defiinitly think about ya
 
igotaneed4speed said:
How long of a turn around are you looking to have this done in? It would take me prob a week or better to get it done.. But im willing to do it .. 200 bucks.. let me know.
Click to expand...


I don't care if takes a week or two, but I'd prefer someone that is close to me so I won't have to tow it that far. I'm in Warren.
 
dave89iroc said:
same here, I could use the money, but way too much going on right now
Click to expand...


I understand all that. I have another project I'm working on right now and I'd rather pay someone else to do it right, instead of dickin around trying to figure it out myself.
 
tewkes28 said:
I understand all that. I have another project I'm working on right now and I'd rather pay someone else to do it right, instead of dickin around trying to figure it out myself.
Click to expand...
Not hard to do yourself and then you know where everything is if something goes wrong...food for thought I did my own and it wasn't bad.
 
LTLHOMER said:
Not hard to do yourself and then you know where everything is if something goes wrong...food for thought I did my own and it wasn't bad.
Click to expand...

The painless kits are very simple.. everythings labled on the wire in print.

Just mount the fuse box pull all the wires to where they go\ or you want them routed. Then cover\wrap all the wires and finish mount before you cut anything to hook it up then start pinning out the connectors and hooking up all the wires.

Solder everything! and use a good shrink wrap NO TAPE!
 
my buddy mike is pretty good at wiring cars...he helped me out alot and has done quite a few of my buddies cars...call him 586-557-6660 tell him johnny told you about him...
 
Woah, how did I miss this?!

Sorry I never got back to ya on that wiring, I never got the e-mail actually. Stupid hotmail probably sent it to junk mail.

Do you still need someone to do this? I don't know if I myself have the time but I know someone who is just as good as me.

Let me know
 
You must log in or register to reply here.
Back
Top