351w

[igotaneed4speed]

Got one thank you MM and Frank.

 

[notch398]

Ive got a complete stock bore Windsor with some edelbrock heads, mild cam, victor intake, etc..no carb...needs to be re-assembled, only tore it down to build a stroker..going a diffrent route..$1500 takes everything, sumped pan, headers..all of it.. more info call me @ 734 417-6785... i have a motor plate for it also.

 

[fastford]

I have a fresh built 393W shortblock and a set of Canfield heads I may be interested in selling.

 

[igotaneed4speed]

Ive got a complete stock bore Windsor with some edelbrock heads, mild cam, victor intake, etc..no carb...needs to be re-assembled, only tore it down to build a stroker..going a diffrent route..$1500 takes everything, sumped pan, headers..all of it.. more info call me @ 734 417-6785... i have a motor plate for it also.

stock pistons and rods?

 

[igotaneed4speed]

I have a fresh built 393W shortblock and a set of Canfield heads I may be interested in selling.

Might or might not be interested if i knew what you wanted for it...

 

[smooth]

there is a complete EFI 351 roller on CL for $450

 

[82hatch]

Have a bare block std bore with crank-$125

 

[notch398]

stock pistons and rods?

yup. also have a csi electric water pump, msd distributor, roller rockers...

 

[fastford]

351W roller block clearanced, bored .030" over, new cam bearings and freeze plugs, ARP main studs
Eagle 3.85" stroke cast steel crank
Scat 5.966" I-beam rods
Probe forged 12cc dish pistons
Clevite 77 bearings
balanced rotating assembly with damper, flex plate and flywheel (both balanced with the assembly seeing as I was unsure of the trans when the shortblock was done).
Comp Cams 232/240 @.050" .570" lift Hyd roller cam, lifters and timing set

Compression will be roughly: 11:1 with 58cc heads, 10.3:1 with 64cc heads, 9.8:1 with 70cc heads

Built for street and mild strip use.

Over $3500 invested, sell for $3000. This is a brand new shortblock still sitting on the stand. I can finish building it and hot test it if interested.

Possible trade for a nice stock 5.0 driver.

 

[bad466]

I have a complete 74 351 out of a Torino I would let go for $200. Call me at 734-218-1781 if interested.

 

[igotaneed4speed]

yup. also have a csi electric water pump, msd distributor, roller rockers...

I'll call you tomorrow but very interested, whats friday look like for you scheduling wise would like to come take a look.

 

[notch398]

I'll call you tomorrow but very interested, whats friday look like for you scheduling wise would like to come take a look.

Was going to take 1/2 day @ work friday... was planning on heading out to milan..i also got the weekend off if that works..jlmk.

 

[igotaneed4speed]

Was going to take 1/2 day @ work friday... was planning on heading out to milan..i also got the weekend off if that works..jlmk.

copy that looks like i'm off on sunday. I'll give you a call saturday to work it out further.

 

[notch398]

copy that looks like i'm off on sunday. I'll give you a call saturday to work it out further.

Sounds good...i will be home all day.

 

[igotaneed4speed]

Ive got a complete stock bore Windsor with some edelbrock heads, mild cam, victor intake, etc..no carb...needs to be re-assembled, only tore it down to build a stroker..going a diffrent route..$1500 takes everything, sumped pan, headers..all of it.. more info call me @ 734 417-6785... i have a motor plate for it also.

Thank you again for the motor and a really good deal!

 

[notch398]

Thank you again for the motor and a really good deal!

No problem and your welcome.